Cryogenic offers strainer cum Air Eliminator for variety of installations and conditions and designed for straining and filtering and elimination of air /vapour from variety of fluids.
As unfiltered liquid enters the strainer cum air eliminator will directly passes through basket in which almost all impurities trapped into the basket and air and vapour travel on the top of the equipment and and only clean liquid without air or vapour content will pass through the outlet of strainer cum air eliminator. Advanced dynamic flow and large filteration area elements ensure low pressure drops and reduce mainteneance period.Also it is designed such that it will not allow any bypassing of the liquid without filteration as basket is prevented by “ O “ Ring seal between basket flange and strainer internal flange. as well as retain position of basket even in case of reverse flow.
This is combination of filteration and elimination space will be reduced which is most common considerable factor for design of Tank Truck Gantry and Tank Wagon Gantry.
Strainer Cum Air Eliminators are normally installed before the measuring devices like Positive displacement meter or turbine meter or Mass Flow Meter which increases accuracy of the measuring devices.
It is used when major part of air is eliminated by header Air Eliminator near storage tank / pump house and very few amount of air / vapour is to be released during tank / wagon loading.
We offer Strainer Cum Air Eliminators from 1” to 24” size with flow range upto 1800 m3/hr (30000 LPM) for pressure range upto 100 bar & design as per ASME Section VIII div I latest eddition.we also offer duplex and jacketed type Strainer cum Air Eliminators.
We have credit of supplying a more than 3000 units by 2018.
SIZE | A END TO END NOZZLE |
B TOP FLANGE TO NOZZLE |
C NOZZLE CENTER TO DRAIN |
D TOP COVER TO BOTTOM DRAIN |
E OVERALL |
WEIGHT IN KGS | |
---|---|---|---|---|---|---|---|
INCHES | MM | ||||||
1.5 | 40 | 450 | 125 | 361 | 515 | 950 | 55 |
2 | 50 | 450 | 125 | 361 | 515 | 950 | 58 |
3 | 80 | 580 | 175 | 320 | 535 | 1000 | 85 |
4 | 100 | 580 | 200 | 345 | 585 | 1050 | 90 |
6 | 150 | 775 | 250 | 750 | 1040 | 1050 | 335 |
Type of strainer – (T1) |
---|
T1 Simplex with top body flange |
T2 Simplex with top body cover with Davit arm. |
T3 Simplex with Quick opening closure. |
T4 Simplex with jacketed. |
T5 Duplex with body flange |
Nominal Size mm – (S) | ||
---|---|---|
S0- 1” ( 25 mm) | S5 – 6” (150 mm) | S10 – 16” (400 mm) |
S1 – 1.5” (40 mm) | S6 – 8” (200 mm) | S11- 18”( 450 mm) |
S2 – 2” (50 mm) | S7 – 10” (250 mm) | S12 – 20”(500 mm) |
S3 – 3” (100 mm) | S8 – 12” (300 mm) | S13- 24” (600 mm) |
S4 – 4” (100 mm) | S9 - 14” (350 mm) | S14- AS PER CUSTOMER'S REQUIRMENT |
Rating - (R) |
---|
R1 – ANSI B 16.5 150# |
R2 – ANSI B 16.5 300# |
R3 - ANSI B 16.5 600# |
Standard flange are Slip on Race face type if Weld Neck type is required pls specify |
Material of construction - (M) |
---|
M1 SA 516 GR.70 (BODY) & ASTM A 105 (FLANGES) |
M2 SA 516 GR.70 (BODY) & SA 352 LF2 (FLANGES) |
M3 IS 2062 GR.B (BODY) & ASTM A 105 (FLANGES) |
M4 SS 304 (BODY) & ASTM A 182 F 304 (FLANGES) |
M5 SS 316 (BODY) & ASTM A 182 F 316 ( FLANGES) |
M6 SA 106 GR B ( BODY) & ASTM A 105 ( FLANGES) |
M7 SA 333 GR 6 ( BODY ) & SA 350 LF2 ( FLANGES) |
* NOTE : All gaskets/Seals will be CS inner /outer with PTFE/Graphite filler and stud /nuts will be ASTM A 193 Gr.B7 / A 194 Gr.2H |
For Stainless Steel and Low temperature service Gasket and Fastners are different. |
Basket and Mesh size - (B) |
---|
B0 Basket with SS 316- 200 mesh |
B1 Basket with SS 316 - 100 mesh |
B2 Basket with SS 316 - 80 mesh |
B3 Basket with SS 316 - 60 mesh |
B4 Basket with SS 316 - 40 mesh |
B5 Basket with SS 316 - 20 mesh |
B6 Customized basket with wire mesh size. |
Flow range – ( F) (It Can be any between Specified Value) | |
---|---|
F0 0- 500 LPM | F6 0 – 6000 LPM |
F1 0 – 1000 LPM | F7 0 – 7200 LPM |
F2 0 - 1500 LPM | F8 0 – 9600 LPM |
F3 0 - 2500 LPM | F9 0 – 10000 LPM |
F4 0 - 3600 LPM | F10 – 0 to Customer Specific Flow rate. |
F5 0 - 4800 LPM |
Operating pressure (P) (normal) |
---|
P1 0 – 6 KG/CM2 |
P2 0 – 10 KG/CM2 |
P3 0 to 15 KG/CM2 |
P4 0 to 25 KG/CM2 |
P5 0 to 50 KG/CM2 |
P6 0 to 75 KG/CM2 |
P7 0 to 100 KG/CM2 |
*Kindly specify If different MOC is required. |
Accessories |
---|
A1 Ball valve for drain and vent. |
A2 Differential pressure gauge with manifold & tubing. |
A3 Differential pressure transmitter with manifold and tubing. |
A4 Differential pressure gauge with reed switch ,manifold and tubing. |
A5 Differential pressure gauge with diaphragm seal. |
A6 Thermal Safety Valve. |
If you want to order all above items kindly insert as A123456. |